Vibration alert function
When a pre-programmed 2-tone/5-tone code or call from a specific user (MDC mode
only) is received, the radio vibrates powerfully enough to be felt through heavy
8 minute voice recorder
a pre-programmed 2-tone/5-tone code or a SelCall (MDC mode only) is received, the
voice recorder automatically starts recording the incoming message. You will not
miss an important call even when you are temporarily away from the radio. You can
manually start recording incoming calls and also your own message. It records up
to a maximum of 8 minutes (Or up to 48 calls of 10 sec. recording time).
700mW audio output
The IC-F50V delivers a loud 700mW* audio output
with the built-in BTL amp. The built-in audio compander provides clear, low noise
communications. Improved bass characteristics also betters the audio quality.
* Typical with internal speaker.
Lone worker function for remote check in
When the radio is not operated for a preset period (1 to 255 min.), the radio sounds
a beep and requires you to push the emergency button. If the emergency button is
not pushed for a preset time (1 to 255 sec.), an emergency signal automatically
transmits and informs your co-worker or dispatcher that something may have happened
to the individual worker.
IP67, dust-tight and waterproof protection
The IC-F50V has outstanding protection against dust and water that is equivalent
to IP67. The IC-F50V can withstand submersion in 1m depth of water for up to 30
minutes and has dust-tight construction that prevents the ingress of dust.
Most popular signalings built-in
Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone and MDC signaling capabilities to set
up your talk group or selective calling. The IC-F50V can decode ten 2-Tone codes
or eight 5- Tone codes on a channel. When a matched tone is received, the following
actions are programmable for each code.
- Bell icon
- Answer back call
- Beep sound
- Auto transmit
- Radio Stun/Kill/Revive
- Voice recorder
- Vibration alert
MDC 1200 Compatible
The following selective calling and ANI features are available with the built-in
- PTT ID
- Radio check
- Caller ID
- Call alert
- Emergency, emergency mic monitoring
- 500 Aliases
- Radio stun/revive
Mode dependent scan
In the mode dependent setting, the scanning setting is dependent on the operating
channel. When you change the operating channel, the scanning list automatically
changes to the operating channel setting. It is convenient when you move to a different
operating area and change an operating channel, you donít have to change the scanning
The Tx channel while scanning can be programmed per scanning list. The talk back
function allows you to transmit on the channel detected after scanning resumes after
a preset time, prior to the Tx channel setting. The nuisance delete function temporarily
deletes a busy channel from the scanning list. Backlight at stop scan automatically
turns on the LCD backlight when the scan stops.
56(W)×97(H)×36.4(D) mm* compact
body with durable, dependable construction, has been tested to MIL standard specifications.
Li-Ion battery pack
The large capacity 1700mAh Lithium-Ion (Li-Ion) battery pack, BP-227 provides a
practical 9–10 hours* of operating time.
* Typical operation Tx:Rx: Stand-by=5:5:90
- 128 memory channels with 8 zones
- Inversion type*1 voice scrambler
- Optional VOX headsets available
- Optional GPS speaker-microphone
- Power ON password
- Radio stun/kill/revive
- 8 DTMF autodial
- Normal and priority scans
- 2-step power saver and 2-step low battery beep
- BIIS 1200 mode programmable
- Busy, repeater lockout functions
- BTL only version (no vibration alert and no voice recorder)available*2
*1 Inversion type voice scrambler is not compatible with UT-109/UT-110
UT-109/UT-110 cannot be physically installed into the IC-F50V.
*2 Not available in some countries.